The Wooden Horse

A NEW ROCKING HORSE

woodhorse — Sat, 21 Jan 2012 20:07:07 +0000

These 2 pictures are views of a new rocking horse. It is made from solid oak, stainedand clear coated. It is about 37 inches across,15 inches deep and 27 inches tall.

LOFTBED PLUS

woodhorse — Fri, 04 Jun 2010 14:33:22 +0000

The customer contacted me to build a twin size loft bed for his son. He wanted it long enough to fit a futon underneath. It took over 45 pieces of wood and many 14-20 pieces of knock down hardware to assemble. the challenge was to make it sturdy over a longer span. Also, as the mattress was not long enough, it was decided to add a short bookcase at one end. The original plan called for a 7 foot height, but that would leave only a foot of head clearance. It was lowered to 6 feet. I was not aware that there was a ceiling fan in the room which may be of some concern. The customer and his son were advised of this concern. You can see a part of the fan in one photo.

FINISHED BOOKCASES

woodhorse — Wed, 20 May 2009 18:57:49 +0000

BOOKCASE/HUTCH and USING GOOGLE SKETCHUP

woodhorse — Mon, 19 Jan 2009 20:02:41 +0000

Image used to show client the requested item

I was contacted by a potential client who wanted a bookcase and a section to store wine and collectables. The client requested it to measure 32 inches wide x 12 inches deep x 84 inches. I started with 2 squares and used the push/pull function to make 2 boxes. The same tool is used to create the shelves. Next rectangles were drawn for the trim and doors. The item was then filled with a knotty pine colour. The glass effect on the doors is made by drawing a rectangle which is tinted with a transparent tone on the material tool function.

Building a Rocking Horse

woodhorse — Fri, 02 Jan 2009 01:22:27 +0000

I selected pine as it is easy to work and is relatively inexpensive. The process is straight forward, but there are a few tricky bits.

1. When lumber is selected, dimensional lumber is used. Even though, it costs more than rough cut lumber. I save time by using prefinished wood…time is money. Lumber should be straight ,thus, avoiding twists or cupping in the wood. Generally, I take the section templates with me to the store. I can use them to do a rough layout ensuring that I have the right amount of lumber.

2. In the shop, the layout is double checked and the pieces are given a final trace . Then all pieces are rough cut to shape and left to acclimatize to the workshop. After a day or two, all pieces are cut to shape on the band saw. A little extra (about 1/8th inch) is left so that I can sand up to the line.

3. Pieces are joined to check for an even fit. Each leg is made from 2 pieces of 3/4 inch pine. The head comprises of 3 sections and the body has five.

4. Contours and edges are rough sanded so that shapes are more defined. I attempt to sand the body contours with a belt sander… portable and table top models. It is slow work to define facial features.

5. Leg pieces are glued up, being careful not to have glue ooze out from the seams. When dry, I drill a 1/4 inch hole to insert a dowel that will reinforce the legs structure.

6. Attaching the head to the body, biscuits are used as they provide strength and aid in alignment of the head to the body. These are cut before any glue ups.

7. Next, the three centre body parts are glued together. When dry, two 1 inch holes are drilled that will house the support posts.

8. Following the head glue up, it is attached to the body.

9. More sanding and shaping, then the outer parts of the body are attached. Throughout, dowels are used to keep the parts in correct alignment.

10. The base is made up of two runners and top platform. They are attached to a box into which, holes for the support posts, have been drilled.

11. Moving onto finer grit of sandpaper, a smoother surface is created.

12. The legs are fastened and the body is slipped onto the support posts which have been inserted in the base.

All that is left is to coat the surface. Will I use a clear coat of polyurethane or stain it to give it character?

HANDMADE WOOD ROCKING HORSE

woodhorse — Fri, 19 Dec 2008 19:41:43 +0000

: Side view

I made the first rocking horse for my daughter over 25 years ago. Over time, the design has evolved and improved. It’s always a joy to make a rocking horse for a child.

Using Google Sketchup to Render Products for Customers

woodhorse — Thu, 11 Dec 2008 19:43:51 +0000

Desk And Chair Cube

woodhorse — Mon, 01 Dec 2008 20:40:09 +0000

Here is another Google Sketchup design for a proposal of a desk and chair cube. It is made of light weight materials (I.e. tubular frame, cloth sides, wood desk top, etc.) When not needed, the chair will slide into the desk.

Wood Whisperer Video

woodhorse — Sun, 23 Nov 2008 23:04:21 +0000

Enjoy this intro to the Wood Whisperer.

Present project: Small Toy Box

woodhorse — Sat, 22 Nov 2008 00:31:54 +0000

A small toy box is on the work table. A rough sketch was made then rendered in Google Sketchup. I find this effective for showing clients an image of their project. It will be made of panels of Knotty pine and stained with Early American wood stain. Safety hinges are used to prevent the lid from coming down too quickly.

A drawing done in Google Sketchup

finished toy box stained with Minwax Early American